ماژول درایور موتور 160Wدو کاناله XY-160D
zoom_out_map
chevron_left chevron_right

ماژول درایور موتور 160Wدو کاناله XY-160D

3011008028

ماژول کنترلر و درایور موتور دو کانال 160 وات 7 آمپر H bridge

تعداد تخفیف واحد قیمت کالا با تخفیف
20 3% 442,320‎تومان
4,560,000‎ریال (با مالیات) 4,560,000‎ریال (بدون مالیات)

Introduction

Double H bridge, can drive two DC motors at the same time, single 7A high power; wide voltage 6.5V ~ 27V ; optocoupler isolated input signal; with isolation and undervoltage protection; comply with EMC EMC design specifications, static discharge circuit , stable and reliable, industrial-grade. Factory direct sales, high power dual DC motor drive, stable and reliable, industrial grade.

1. The power supply voltage is 6.5V-27V. The power supply must not be connected or exceed 27V. Otherwise, the module may be burned out. It is recommended to connect the 15A fuse in series with the power input .
2. Two-way motor interface, each rated output current is 7A , peak current is 50A, and the motor interface must not be short-circuited. It is recommended to connect 10A fuses in series .
3. The control signal voltage is 3-6.5V, which is the enable signal and the forward and reverse control signals , respectively .
4. Enable signal terminal (ENA) input PWM adjustable speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us.
5. Working temperature -25 ° C -80 ° C.
6. Product size: 55*55*16mm (length, width and height).
7. Mounting hole diameter: 3mm, pay attention to prevent short circuit of the back circuit during installation , you can add insulation pad or copper column to raise the circuit board .
8. Weight: 20 g.

Suitable motor:
For motors with rated voltage of 24V , it is suitable to identify the rated power of 115W and below or the rated current of 7A or less .
For motors with rated voltage of 12V , it is suitable to identify the rated power of 40W and below or the rated current of 7A or less .
Precautions:
1. The driver power supply must not be reversed. It is recommended to connect the 15A fuse in series at the power interface . The voltage should be between 6.5 and 27V . If the voltage is over voltage, powering up may burn the drive module.
2. It is recommended that the rated output current of the power supply be more than 2 times of the rated current of the motor , so as not to cause the power supply to supply the current required by the motor to cause the power supply voltage to fall, so that the power supply voltage does not reach the input voltage required by the driver, so that the drive module performs undervoltage protection. The broken output causes the motor to stall.
3. The motor interface must not be short-circuited, otherwise the drive module may be burned. It is recommended to connect the 10A fuse at the motor interface .
4. In the forward and reverse switching, you need to brake for more than 0.1S and then reverse. It can't be reversed when the motor has not stopped. Otherwise, the drive may be damaged.
5. When the drive module is powered down, do not rotate the motor directly or indirectly at high speed, otherwise the electromotive force generated by the motor may burn the drive module. If the application needs to rotate the motor at high speed when the drive module is powered down, it is recommended to connect a relay (the NO and COM terminals are connected in series) to the motor interface of the drive. The relay coil and the driver are connected to the power supply. Thus, when the power supply is powered down, the relay disconnects the drive from the motor.
6 . Be careful not to get wet of the drive. Do not short-circuit the components on the drive board. Do not touch the pins and pads of the components on the board.
7. Please read the baby description carefully before use. If the module is damaged due to wrong use, it will not be returned.

Specification

1. Double H bridge, which can drive two DC motors at the same time, single 7A current, high power;
2. Wide voltage input 6.5V ~ 27V ;
3. Signal optocoupler isolated input, can be directly controlled by IO port, free from interference;
4. Undervoltage protection to prevent instantaneous high current burning of the module;
5. High-power TVS and electrostatic bleeder circuit, which suppresses transient interference pulse and static electricity, enhances EMC performance, and is stable and reliable, industrial grade design. 

Control signal logic
Note: 0 is low, 1 is high, × is any level, and it is high when floating .
1. 1# motor interface control signal logic

IN1

IN2

ENA 1

OUT1 OUT2 output

0

0

×

brake

1

1

×

Hanging

1

0

PWM

Forward speed

0

1

PWM

Reverse speed regulation

1

0

1

Full speed forward

0

1

1

Full speed reversal

2. 2# motor interface control signal logic

IN3

IN4

EN A2

OUT3 OUT4 output

0

0

×

brake

1

1

×

Hanging

1

0

PWM

Forward speed

0

1

PWM

Reverse speed regulation

1

0

1

Full speed forward

0

1

1

Full speed reversal

16 محصول مشابه
امتیاز شما

  • احمد یلمه | حدود 1 سال قبل
    با سلام این درایور را میتونم به خروجی درایور دو استپر موتور وصل کنم تا قدرت لازم برای استپر موتور ۷ آمپر را فراهم کنم یعنی توان درایور استپر موتور را افزایش بدم؟ لطفأ راهنمایی کنید
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | حدود 1 سال قبل
      سلام ، خروجی گرفتن از یک کانال برای اتصال دو استپ موتور برای درایو امکان پذیر نیست
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
  • محمد جوانی | بیش از 3 سال قبل
    این درایور قابلیت چپگرد و راستگرد رو داره؟
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | بیش از 3 سال قبل
      سلام، با عوض کردن سیم های ورودی به موتور قابل انجام است.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
  • ابوالفضل منافی | بیش از 3 سال قبل
    300 گرم؟
    مطمئنید؟
    فکر کنم باید کمتر از اینا باشه..
    پاسخ | گزارش
    0 thumb_down
    1 thumb_up
    • پشتیبانی فروشگاه | بیش از 3 سال قبل
      وزن این ماژول 30g می باشد. اطلاعات اصلاح گردید.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
  • ابوالفضل منافی | بیش از 3 سال قبل
    سلام
    ببخشید وزنش حدودا چند گرمه؟؟
    و این درایور قابلیت اتصال به آردوینو برای تنظیم دور موتور ها داره؟؟
    باتشکر
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | بیش از 3 سال قبل
      سلام،وزن این ماژول 30g بوده و قابلیت استفاده با آردوینو را برای کاربرد مورد نظر دارد.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
ویرایش نظر
  یا لغو