برد شارژر وایرلس 5W مدل HW-225
zoom_out_map
chevron_left chevron_right

برد شارژر وایرلس 5W مدل HW-225

3011015139

برد شارژر وایرلس 5 وات دارای ولتاژ گیرنده 5 ولت

0‎ریال (با مالیات) 0‎ریال (بدون مالیات)
اتمام موجودی

توجه: این برد بدون صفحه کویل شارژ ارائه می شود.

معرفی
ورودی این ماژول 5 ولت می باشد که می توان از طریق پورت میکرو USB به آن اعمال نمود. روی این ماژول دو عدد LED تعبیه شده است که نمایشگر روشن بودن و انجام عملیات شارژ است.

چراغ قرمز رنگ روی ماژول HW-225 هنگام شارژ روشن می شود و چراغ سبز خاموش می شود پس از اتمام شارژ ، چراغ قرمز خاموش است و چراغ سبز روشن می شود.

این برد شارژ بی سیم قدرت تشخیص شی خارجی را دارد. به گونه ای که اگر یک جسم خارجی فلزی روی سیم پیچ فرستنده ماژول قرار بگیرد ، پس از جدا شدن ، چراغ قرمز خاموش می شود و چراغ سبز روشن می شود.

Introduction

This product is made of high quality ABS material, strong and durable.
HW-225 wireless charging transmitter module, compatible with WPC standard wireless receiver.
Low static power consumption, high efficiency, and maximum support for 5W charging power.
Carefully welding, precise hole position, complete functions.
Double LED indicator, which can display the module in the state of power-on, charging, charging saturation, foreign object detection (FOD).

Specification

Material: ABS
Size: Approx. 5*5*0.3cm/1.97*197*0.12inch
Rated operational voltage: DC +5V
Working Temperature: -20-85℃
Storage Temperature: -40-125℃
When the power is turned on, the green LED on the HW-225 lights up
Charge the center of the back of the HW-225 module with the wireless charging function on the back center of the phone (note: the positional offset of the phone placed on the module coil will affect the charging effect), and the red on the HW-225 module during charging. The light LED will illuminate and the green LED will be off
After charging is completed, the red LED is off and the green LED is lit
The HW-225 wireless charging module has a foreign object detection function. When there is a metal foreign object on the transmitting coil of the module, the red LED and the green LED flash, after the metal foreign object is removed, the red LED is extinguished, and the green LED is lit.
The limit operating voltage of this product cannot exceed 5.5V DC.
Standard: Qi Wireless Charging Standard
Standby power: average power is less than 50 mW Conversion
efficiency: greater than 73%
Transmission Distance: Maximum 10 mm.
Recommended Transceiver Distance 2 mm~4 mm
Input voltage: DC4.3V~5.5V/1.5~2A, alarm and stop charging in this voltage range
Output voltage: 5V±0.1V
Charging current: 500mAh - 1000mAh
Charging power: up to 5W
Overtemperature protection: When the temperature is higher than 60℃ It will automatically stop charging for one minute, then lower the temperature, and it will recharge. Overcurrent protection: When the current exceeds 1.5A, it will automatically stop charging.

Instruction

1. When the power is switched on, the green LED on HW-225 lights up. 2. The mobile phone with wireless charging function is charged on the coil of HW-225 module with the back center corresponding to the coil center of HW-225 module (note: the position deviation of the mobile phone placed in the coil of the module will affect the charging effect). 3. During the charging process, the red LED on the HW-225 module will light up and the green LED will be extinguished. After charging, the red LED goes out and the green LED lights up. 4. HW-225 wireless charging module has the function of foreign body detection. When there is metal foreign body on the transmitting coil of the module, red LED and green LED flicker. After removing the metal foreign body, red LED extinguishes and green LED lights up. Note: Please allow 1-3mm differs due to manual measurement.

16 محصول مشابه
امتیاز شما

  • یاشار پارسا | بیش از 2 سال قبل
    سلام برد گیرنده رو من در فروشگاه ندیدم... ایا موجوده؟
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | بیش از 2 سال قبل
      سلام، خیر.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
  • Saeed Pa | بیش از 2 سال قبل
    سلام
    دوست عزیز من گوشیم قابلیت شارژ وایرلس رو داره ، چطور میتونم از این ماژول براش استفاده کنم
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | بیش از 2 سال قبل
      سلام، اگر صفحه کویل شارژ داشته باشید این ماژول برایتان قابل استفاده خواهد بود.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
  • علی اسماعیلی | بیش از 2 سال قبل
    این برد گیرنده هست یا فرستنده؟
    برای تهیه کویل باید چیکار کرد؟
    پاسخ | گزارش
    0 thumb_down
    0 thumb_up
    • پشتیبانی فروشگاه | بیش از 2 سال قبل
      سلام، این برد فرستنده است و کویل تنها در فروشگاه موجود نیست.
      پاسخ | گزارش
      0 thumb_down
      0 thumb_up
    • امیر رضا عجم زاده | بیش از 2 سال قبل
      اگر میخوای ولتاژ صحیح و با جریان مناسب از کویل بگیری ۲۵ دور سیم لاکی 0.45 و یا 0.5 رو به طور منظم روی یه صفحه صاف به صورت حلزونی بپیچ و با چسب قطره ای و یا اپوکسی ثابتش.کن...فقط حواست باشه که تعداد دور کویل اولیه ۲/۵ دور نیست ، ۲۵ دور هست ، و ثانویه رو هم ۳۲ دور سیم لاکی 0.65 و یا 0.7 رو مثل اولیه بپیچ و خروجی کویل رو به یه رگولاتور ولتاژ lm7805 بده و خروجی مثبتت رو بعد از رد کردن از یک عدد دیود به سوکت نری شارژر گوشیت وصل کن و اگر میخوای برد دوم و یا همون گیرنده ولتاژ پشت قاب گوشیت جا بشه سعی کن از قطعات smd مخصوص این کار استفاده کنی که هم ظاهر کار تمیزتر باشه و هم سایزش کوچیکتر ، و اگر میخوای بیشترین بازدهی رو بگیری سعی کن فاصله دو تا کویل فرستنده و گیرنده از 5mm یا همون (۵ میلیمتر) بیشتر نباشه.
      شرمنده اگه طولانی شد...
      پاسخ | گزارش
      1 thumb_down
      1 thumb_up
ویرایش نظر
  یا لغو