ماژول درایور چراغ قوه 10 وات Micro-USB طرح Side مدل JZ-1011
معرفی
ماژول کاهنده ولتاژ 3 آمپری DC-DC این ماژول، مبدل باک با جریان خروجی 3 آمپر است. در این مبدل امکان تغییر ولتاژ توسط پتانسیومتر قرار گرفته شده بر روی ماژول وجود دارد. در حالت پیک جریان تا 3A می توان خروجی گرفت.
مشخصات
محدوده دمای کاری:۸۵+ ~ ۴۰-
ولتاژ ورودی : 4.5 تا 24 ولت
ولتاژ خروجی:1.8 تا 12 ولت
Features
With a new original US chip, the output current is up to 3A, and the long-term operation is 2.1A. Output can be set to adjustable voltage and fixed voltage.
With a new solution design, the circuit design does not require electrolytic capacitors and tantalum capacitors (electrolytic capacitors have a short lifetime and the tantalum capacitors are in danger of explosion).
The new scheme adopts synchronous rectification, and the circuit conversion efficiency is very high. When the 6.5V to 5V 0.7A, the efficiency is as high as 97.5%, and when 12V turns 5V 1A, it also reaches 94%.
High current shielding inductors and ultra-low internal resistance maximize conversion efficiency. Reduce heat.
Mini, 20 (L) * 11 (W) * 5 (H) mm. Ultra-low static current, static current 0.85 mA. Connecting to car batteries without switching, can be on the cigarette lighter line, or on the ACC power line.
Specification
Input Voltage: DC 4.5-24V
Conversion Efficiency: 97.5% (highest) (6.5V to 5V, 0.7A)
Switch Frequency: 500KHz
Output Ripple: 20mV(12V to 5V, A) 20M width
Output Over-voltage Protection: no
Temperature rising range at full load: 40℃
Static Current: 0.85mA
Voltage Adjustment Rate: ±0.5%
Dynamic Response Speed: 5% 200uS
Output Short-circuit Protection: yes, please don’t keep making it short-circuit.
Output Reverse Connection Protection: no
Wiring Method: soldering
Input Method: soldering
Output Method: soldering or pins
Welding Hole Spacing: 2.54mm
Operating Temperature: -40℃ ~ +85℃(Industrial class) (The higher the operation temperature is, the smaller the output power is)
Output Voltage: Integrated adjustable and fixed output (Adjustable range is 0.8-17V, fixed output are 1.8V, 2.5V, 3.3V, 5V, 9V, 12V that can be chosen on the back side)
Output Current: 3A max (please enhance cooling work when it is full load); When real tested input 12V and output is 1.5A, no need to add special system.
Enable Function Control: yes, Low electric level will stop working when high electric level is working. High electric level is 2-5V, low electric level is 0V or so.
-
علی راجی | 3ماه قبل سلام. میشه به این ماژول ولتاژ مثلا ۹ داد و با اون قسمت جامپر ها ولتاژ خروجی ثابت ۱۲ گرفت؟! یا کاهنده هست فقط؟
-
پشتیبانی فروشگاه | 3ماه قبل سلام
کاهنده می باشد و ولتاژ ورودی می بایست از ولتاژ خروجی بالاتر باشد تا عملیات کاهش ولتاژ انجام شود.
-
-
Ali Aslani | 4ماه قبل لطفاً موجود کنید-
بخش فروش ( پاسخ به : Ali Aslani ) | 4ماه قبل سلام خدمت دوستان عزیزی که منتظر این کالا بودند. این کالا در مورخ 1402/08/29 مجددا تامین موجودی گردید.
-
-
نعیم تشکر | 5ماه قبل EN = Enable. Active HIGH and pulled HIGH on the module. Pull LOW to disable the module output. IN+ = Input voltage GND = Ground VO+ = Output voltage
-
حسین معصومی | حدود 1 سال قبل سلام
میبخشید ماژول کاهنده
ماژول DC-DC کاهنده 3 آمپر MP2315 با خروجی 1.8 الی 12 ولت
میشه لطف کنید خروجی ورودی رو توضیح بدهید ممنون میشم-
پشتیبانی فروشگاه | حدود 1 سال قبل سلام ، در تصاویر توضیحات ورودی و خروجی کاملا توضیح داده شده است.
-
-
حسين گلشیک | حدود 1 سال قبل این جالبه. لطفا موجودش کنید