ماژول مبدل DC-DC کاهنده 5 آمپر XL4015
Introduction
The IIC level shifter enables different signal levels of two IIC devices to communicate, and the 1.2V-3.3V reference level and the 1.8V-5.5V reference level are converted to each other. The low internal on-resistance allows for lower signal propagation delays. It is also possible to enable two different communication rate IIC devices to achieve normal communication, such as 400KHz on one side of the converter and 100KHz on the other side, but the maximum communication rate of the system is slightly less than 100KHz. Because of the small signal propagation delay, the device is mainly used for Works with SMBus devices and standard mode, fast mode and ultra fast mode Plus I2C bus devices. The maximum frequency depends on the RC time constant, but usually supports > 2 MHz.
The IIC level shifter cannot physically isolate the capacitor on either side of the bus. The bus capacitance on both sides should be limited to 400pF. If it is exceeded, the IIC bus buffer repeater should be connected. The PCA9306 can only isolate the two sides when the device is disabled and provides a voltage level shift upon activation. It is more advantageous than a discrete transistor voltage conversion solution because the switch is manufactured symmetrically, and the converter provides excellent ESD for low voltage devices. Protection while protecting lower ESD devices, the device's SCL and SDA are open-drain output devices.
Specification
Board VCC: 0V ~ 5.5V
Chip working reference voltage: Vref1, Vref2: 0V~5.5V
Working environment temperature: -40 ° C ~ 85 ° C
-
میرمحمد حسینی | بیش از 2 سال قبل لطفا ماژول درایور مدل IIC-I2C برای lcd های 16*2 رو هم موجود کنید-
پشتیبانی فروشگاه | بیش از 2 سال قبل سلام، پیشنهاد شما برای بررسی به بخش واردات ارجاع داده شد. از حسن توجه شما سپاس گزاریم.
-
-
فرزاد فروتن | بیش از 3 سال قبل سلام میشه کاربرد ها هم بنویسید-
پشتیبانی فروشگاه | بیش از 3 سال قبل سلام، برای کاربردهایی که نیاز به ارتباط دو طرفه با پروتکل I2C و SMBUS می باشد و دارای مبدل سطح ولتاژ هم باشد.
-
-
هادی مداح | بیش از 3 سال قبل ببخشید از چه ماژولی برای شارژ کردن باطری خودرو استفاده کنیم ولتاژ ورودی 5 ولت وامپر 1.5 داریم و برق اینورتر شبه سینوس 12 به 220 هم داریم در ورودی ماژول چه ولتاژ وامپری بدهیم که باطری خودرو را شارژ نماید اگر فروشگاه شما هم ندارد امکانش هست راهنمایی بفرمایید با تشکر از سایت خوبتون-
پشتیبانی فروشگاه | بیش از 3 سال قبل سلام، برای شارژ باتری ماشین بهتر است ولتاژ شارژ کمی بالاتر از 12 ولت باشد(حدود 12.3). توصیه می شود از مداری استفاده شود که دارای حفاظت هایی مانند شارژ کنترل و... باشد.
-